Schaff Piano Product Catalog - page 57

57
RESTRINGING TOOLS AND ACCESSORIES
STRINGING HOOK
New style non-breakable plastic handle
is 3-1/2” long and is fitted with a 4” long string
hook for lifting coils tight and neat around
tuning pins.
No. 135S -
Stringing Hook. Each
OFFSET STRINGING HOOK
Same as our No. 135S above except the
stringing hook has an offset angle as it extends
from the handle. (not shown)
No. 135C -
Offset Stringing Hook. Each
MANNINO STRING HOOK
This is a factory-style string hook, useful
when installing strings or when leveling strings
for voicing. The tool has a wide but thin tip,
narrow enough to drop between the strings of a
unison without turning the tool, but wide
enough to give strength for pulling up on the
wire. You can merely drop it down between the
strings and hook the wire in one easy motion
for string leveling.
Special Note:
This hook is
designed for string leveling and string voicing
work. It is not intended to serve as a coil lifting
hook during restringing, as the tip could wear
and break prematurely.
No. 89 -
Mannino String Hook. Each
STRING STRETCHER
A necessary tool for any restringing job. Rolling the 1-7/8”
diameter brass wheel over newly installed piano core wire
will stretch the wire and help tighten the coils. Overall
length is 11”.
No. 132 -
String Stretcher. Each
TUNING PIN CRANK
Traditional hardwood handle style has a square tip opening
that fits onto tuning pins for easily winding coils. The nickel
plated steel crank measures 3” in width from the shaft
centers.
No. 109 -
Tuning Pin Crank. Each
TUNING PIN SETTER
Used for driving tuning pins when they must be set further
into the pin block. Spring loaded plunger sets firmly on the
tuning pin and prevents any hammer damage. The 6” long,
chrome plated handle allows pin to be held in position to
prevent string from slipping.
No. 108 -
Tuning Pin Setter. Each
POWER TUNING PIN SOCKET
Triangular shank one end, star
tip on other. For use with power
tools to remove tuning pins. 3-1/2” long, nickel plated
No. 63 -
Power Tuning Pin Socket, Star Recess. Each
TUNING PIN SOCKET
FOR BRACE
One end has a star tip, the other
end is a tapered square to fit a hand brace. Socket is
designed for tuning pin removal. 3” long, chrome plated.
No. 25 -
Tuning Pin Socket for Brace. Each
TUNING PIN EXTRACTOR
Used for removing broken tuning pins. The
tapered and reverse threads cut into broken
tuning pins for easy extraction. Tool, measuring 1-3/4” long,
can be used with a hand brace, “T” style lever or any
standard tuning lever.
No. 110 -
Tuning Pin Extractor. Each
STRINGING HOOK WITH WOOD HANDLE
A convenient style stringing hook with wood handle.
No. 3150 -
Stringing Hook with Wood Handle. Each
RATCHET HEAD
Tough alloy steel. Will stand
up under rugged factory use.
For use with power tools to drive tuning pins. 3/8” square
socket one end, star recess on other end. 2-3/4” long,
nickel plated.
No. 23 -
Ratchet Head, Star Recess. Each
ROBINSON STRATE-MATE
An extremely fast and efficient tool for voicing the music wire
itself. STRATE-MATE stretches piano strings by lifting them
slightly off the bridge, thus equalizing all the segments along
the length from the tuning pin to the hitch pin. Furnished
with instructions.
No. 6015 -
Strate-Mate. Each
0...,47,48,49,50,51,52,53,54,55,56 58,59,60,61,62,63,64,65,66,67,...186
Powered by FlippingBook